ts78m00 series 3 - terminal 500ma positive voltage regulator 1 / 10 version: b 07 to - 220 to - 252 (dpak) general description the ts78m00 series positive voltage regulators are identical to the popular ts7800 series devices, except that they are specified for only half the output current. lik e the ts7800 devices, the ts78m00 series 3 - terminal regulators are intended for local, on - card voltage regulation. internal current limiting, thermal shutdown circuitry and safe - area compensation for the internal pass transistor combine to make these devic es remarkably rugged under most operating conditions. maximum output current with adequate heatsink is 500ma features output voltage range 5 to 24v output current up to 500ma no external components required internal thermal overload protection internal short - circuit current limiting output transistor safe - area compensation output voltage offered in 4% tolerance ordering information part no. package p acking ts78m xx cz c0 to - 220 50pcs / tube ts78m xx cp ro to - 252 2.5kpcs / 13 reel note: where xx denote voltage option standard application circuit a common ground is required between the input and t he output voltages. the input voltage must remain typically 2.0v above the output voltage even during the l ow point o n the input ripple voltage. xx = these two digits of the type number indicate voltage. * = cin is required if regulator is located an appreciable distance from power supply filter. ** = co is not needed for stability; however, it does improve transient response. absolute maximum rating ( ta = 25 o c unless otherwise noted ) parameter symbol limit unit input voltage v in * 35 v input voltage v in ** 40 v power dissipation p d internal limited w operating junction temperature t j 0~+125 o c storage temperature range t stg - 65~+150 o c note: * ts78 m 05 to ts78 m 18 ** ts78 m 24 *** follow the derating curve pin definition : 1. input 2. ground (tab) 3. output
ts78m00 series 3 - terminal 500ma positive voltage regulator 2 / 10 version: b 07 ts78 m 05 electrical characteristi cs (v in =10v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 4. 80 5 5. 20 output voltage vout 7 .5 v vin 20v, 5 ma iout 350ma 4.75 5 5.25 v 7.5v vin 25v -- 3 100 line regulation regline tj=25 o c 8v vin 12v -- 1 50 5 ma iout 500ma -- 15 100 load regulation regload tj=25 o c 5ma iout 200ma -- 5 50 mv quiescent current iq iout=0, tj=25 o c -- 3 6 7 .5 v vin 25v -- -- 0.8 quiescent current change " iq 5 ma iout 350ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 40 -- #v ripple rejection ratio rr f=120hz, 8v vin 18v 62 78 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f =1khz -- 17 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 5 ma, 0 o c tj 125 o c -- - 0.2 -- mv/ o c ts78 m 08 electrical characteristi cs v in =1 4 v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 7.69 8 8.32 output voltage vout 10.5v vin 23v, 5 ma iout 350ma 7.61 8 8.40 v 10.5v vin 25v -- 6 160 line regulation regline t j=25 o c 11v vin 17v -- 2 80 5ma iout 500ma -- 12 160 load regulation regload tj=25 o c 5ma iout 200ma -- 4 80 mv quiescent current iq iout=0, tj=25 o c -- 3 6 10.5v vin 25v -- -- 0.8 quiescent current change " iq 5ma iout 350ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 52 -- #v ripple rejection ratio rr f=120hz, 11v vin 21v 56 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 16 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 5ma, 0 o c tj 125 o c -- - 0.2 -- mv/ o c ? pulse testing techniques are us ed to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ? this specification applies only for dc power dissipation permitted by absolute maximum ratings.
ts78m00 series 3 - terminal 500ma positive voltage regulator 3 / 10 version: b 07 ts78 m 09 ele ctrical characteristics (v in =1 5 v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 8.65 9 9.36 output voltage vout 1 1 .5v vin 23v, 5 ma iout 350ma 8.57 9 9.45 v 11.5v vin 26v -- 6 180 li ne regulation regline tj=25 o c 1 2 v vin 17v -- 2 90 5ma iout 500ma -- 12 180 load regulation regload tj=25 o c 5ma iout 200ma -- 4 90 mv quiescent current iq iout=0, tj=25 o c -- 3 6 11.5v vin 26v -- -- 0.8 quiescent current change " iq 5ma iout 350ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 52 -- u v ripple rejection ratio rr f=120hz, 12 v vin 2 2 v 55 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 16 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 5 ma, 0 o c tj 125 o c -- - 0.2 -- mv/ o c ts78 m 12 electrical characteristics (v in =1 9 v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 11.53 12 12.48 output voltage vout 14.5v vin 27v, 5ma iout 350ma 11.42 12 12.60 v 14 .5 v vin 30v -- 10 240 line regulation regline tj=25 o c 15v vin 19v -- 3 120 5ma iout 500ma -- 12 240 load regulation regload tj=25 o c 5ma iout 200ma -- 4 120 mv quiescent cur rent iq tj=25 o c , iout=0 -- 3 6 14.5v vin 30v -- -- 0.8 quiescent current change " iq 5ma iout 500ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 75 -- u v ripple rejection ratio rr f=120hz, 15v vin 25v 55 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 18 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout=5ma, 0 o c tj 125 o c -- - 0.3 -- mv/ o c ? pulse testing techniques are use d to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ? this specification applies only for dc power dissipation permitted by absolute maximum ratings.
ts78m00 series 3 - terminal 500ma positive voltage regulator 4 / 10 version: b 07 ts78 m15 ele ctrical characteristics (v in =23v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 14.42 15 15.60 output voltage vout 17.5v vin 30v, 5 ma iout 350ma 14.28 15 15.7 5 v 17.5v vin 30v -- 12 300 line regulation regline tj=25 o c 18v vin 22v -- 3 150 5ma iout 500ma -- 12 300 load regulation regload tj=25 o c 5ma iout 200ma -- 4 150 mv quiescent current iq tj=25 o c , iout=0 -- 3 6 17.5v vin 30v -- -- 0.8 quiescent current change " iq 5 ma iout 500ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 90 -- #v ripple rejection ratio rr f=120hz, 18v vin 28v 54 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f=1k hz -- 19 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 10 ma, 0 o c tj 125 o c -- - 0.3 -- mv/ o c ts78 m 18 electrical characteristics (v in =24v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 17.30 18 18.72 output voltage vout 21v vin 33v, 5ma iout 350ma 17.14 18 18.90 v 21v vin 33v -- 15 360 line regulation regline tj=25 o c 22v vin 26v -- 5 180 5ma iout 500ma -- 12 360 load regulation regload tj=25 o c 5ma iout 200ma -- 4 180 mv quiescent curren t iq tj=25 o c , iout=0 -- 3 6 21v vin 33v -- -- 0.8 quiescent current change " iq 5ma iout 500ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 110 -- u v ripple rejection ratio rr f=120hz, 21v vin 31v 54 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f =1khz -- 22 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 5ma, 0 o c tj 125 o c -- - 0.5 -- mv/ o c ? pulse testing techniques are use d to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ? this specification applies only for dc power dissipation permitted by absolute maximum ratings.
ts78m00 series 3 - terminal 500ma positive voltage regulator 5 / 10 version: b 07 ts78 m 24 elec trical characteristics v in =33v, iout=350ma, 0 o c tj 125 o c , cin=0.33 u f, cout=0.1 u f; unless otherwise specified.) parameter symbol test condition min t yp m ax u nit tj=25 o c 23.07 24 24.96 output voltage vout 2 7 v vin 38v, 5ma iout 350ma 22.85 24 25.20 v 2 7 v vin 38v -- 18 480 line regulation regline tj=25 o c 2 8 v vin 32v -- 6 240 5ma iout 500ma -- 12 480 load regulation regload tj=25 o c 5ma iout 200ma -- 4 240 mv quiescent current iq iout=0, tj=25 o c -- 3 6 2 7 v vi n 38v -- -- 0.8 quiescent current change " iq 5ma iout 500ma -- -- 0.5 ma output noise voltage vn 10hz f 100khz, tj=25 o c -- 170 -- #v ripple rejection ratio rr f=120hz, 2 7 v vin 3 7 v 54 80 -- db voltage drop vdrop iout=500ma, tj=25 o c -- 2 -- v output resistance rout f=1khz -- 2 8 -- m output short circuit current ios tj=25 o c -- 50 -- ma peak output current io peak tj=25 o c -- 0.7 -- a temperature coefficient of output voltage " vout/ " tj iout= 5 ma, 0 o c tj 125 o c -- - 0.5 -- mv/ o c ? pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. ? this specification appl ies only for dc power dissipation permitted by absolute maximum ratings.
ts78m00 series 3 - terminal 500ma positive voltage regulator 6 / 10 version: b 07 electrical characteristics curve figure 1. worst case power dissipation vs. ambient temperature (to - 220) figure 2. peak output current vs. dropout voltage figure 3. bias current vs. input voltage figure 4. dropout voltage vs. junction temperature figure 5. bias current vs. output current figure 6. ripple rejection vs. frequency
ts78m00 series 3 - terminal 500ma positive voltage regulator 7 / 10 version: b 07 application information f igure 7 . dpak thermal resistance and ma ximum power dissipation vs. p.c.b copper length
ts78m00 series 3 - terminal 500ma positive voltage regulator 8 / 10 version: b 07 to - 220 mechanical drawing marking diagram xx = output voltage (05=5v, 08=8v, 09=9v, 12=12v, 15=15v, 18=18v, 24=24v) y = year code m = month code ( a =jan, b =feb , c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) l = lot code cz = package code for to - 220 to - 220 dimension millimeters inches dim min max min max a 10.000 10.500 0.394 0.413 b 3.740 3.910 0.147 0.154 c 2.440 2.940 0.096 0.116 d - 6.350 - 0.250 e 0.381 1.106 0.015 0.040 f 2.345 2.715 0.092 0.058 g 4.690 5.430 0.092 0.107 h 12.700 14.732 0.500 0.581 i 8.382 9.017 0.330 0.355 j 14.224 16.510 0.560 0.650 k 3.556 4.826 0.140 0.190 l 0.508 1.397 0.020 0.055 m 27.700 29.620 1.060 1.230 n 2.032 2.921 0.080 0.115 o 0.255 0.610 0.010 0.024 p 5.842 6.858 0.230 0.270
ts78m00 series 3 - terminal 500ma positive voltage regulator 9 / 10 version: b 07 to - 252 mechanical drawing marking diagram xx = output voltage (05=5v, 08=8v, 09=9v, 12=12v, 15=15v, 18=18v, 24=24v) y = year code m = month code ( a =jan, b =feb, c =mar, d =apl, e =may, f =jun, g =jul, h =aug, i =sep, j =oct, k =nov, l =dec) l = lot code cp = package code for to - 252 to - 2 52 di mension millimeters inches dim min max min max a 2.3bsc 0.09bsc a1 4.6bsc 0.18bsc b 6.80 7.20 0.268 0.283 c 5.40 5.60 0.213 0.220 d 6.40 6.65 0.252 0.262 e 2.20 2.40 0.087 0.094 f 0.00 0.20 0.000 0.008 g 5.20 5.40 0.205 0.213 g1 0.75 0.85 0.030 0.033 g2 0.55 0.65 0.022 0.026 h 0.35 0.65 0.014 0.026 i 0.90 1.50 0.035 0.059 j 2.20 2.80 0.087 0.110 k 0.50 1.10 0.020 0.043 l 0.90 1.50 0.035 0.059 m 1.30 1.70 0.051 0.67
ts78m00 series 3 - terminal 500ma positive voltage regulator 10/ 10 version: b 07 notice specifications of the products displayed herein are subject to change without notice. tsc or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. information contained herein is intended to provide a product description only. no license, express or implied , to any intellectual property rights is granted by this document. except as provided in tsc s terms and conditions of sale for such products, tsc assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use o f tsc products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. the products shown herein are not designed for use in medical, life - saving, or life - sustaining applications. customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify tsc for any damages resulting from such improper use or sale.
|
